# Retaining Walls with Curves

Video: Build a Retaining Wall

with Outside Curves

Video: Build a Retaining Wall

with Inside Curves

## Curves & Serpentines

Whether you choose soft curved retaining walls or classic straight retaining walls, Allan Block has the system to satisfy every design.

Curves accent any landscape, are simple to design and easy to build. Consider how tight or gentle you want the curves to be and choose the block or combination of blocks that are best suited for your design. See the radius chart for more information.

### Determining the Radius

Minimum radius of a retaining wall

Curved walls have a greater setback, which causes a coning effect to occur causing your retaining wall to have its tightest radius at the top of the wall which in turn creates the need for a larger radius at the base course.

The final height of the wall will determine what the minimum radius at the base course must be. Use the radius chart to determine what the minimum recommended radius of the base course of the wall needs to be, so the top course of the wall will not be less than 1.2 m.

Depending on the block you choose, the tightest radius at the top of the retaining wall is:

- AB Collection
- Full size block is 1.2 m
- half width block is 0.8 m

### Starting the Curve

How to start a curve

From the point of where the curve will start, measure straight back from the wall the required amount (shown in the radius chart) and drive a stake into the ground. This will be the center of the curve. Attach a string line to the stake the length of the radius and rotate it around to mark the location of the base course. Install the blocks with the front of the blocks lining up with the mark.

- To transition the curve back into a straight wall or another curve, lay out the curve and the first couple blocks of the next section. Adjusting 1 or 2 of the blocks will help in the transition of the next section of the retaining wall.

### Building Tighter Curves with AB or AB Europa Walls

Cutting the bottom notch for tighter inside curves

Cutting the bottom notch for tighter outside curves

- Use the AB Jumbo Junior whenever possible to build tighter curves within the wall
- When using full size blocks, it may be necessary to remove parts of the bottom notch to fit the blocks closer together.

### Curves with Reinforcement

Inside Curves with Geogrid

Outside Curves with Geogrid

When placing geogrid along curved walls, the geogrid should follow the back of the lip on the retaining wall block. Simply slit the geogrid with a utility knife and either feather out or overlap to follow the curve.

### Inside Curves and Geogrid

Geogrid needs to have 100% coverage around any curve. To achieve this, additional layers need to be installed above the course where the geogrid is required to fill voids that are created.

- Roll out the AB Reinforcement Grid behind the wall, keeping the edge of the geogrid tight against the front of the blocks. Voids will appear between the pieces at the back. Trim the geogrid to fit along the front lip of the blocks.
- Mark the blocks or take note of the areas where the voids are in the geogrid placement.
- On the next course of block, place geogrid over the marked areas covering the voids.
- On patterned walls, fit the grid through the coursing as best as possible to fill the void from the course below.

### Outside Curves and Geogrid

- Roll out the AB Reinforcement Grid around the curve. Trim to fit along the front lip of the blocks.
- Lift the section of geogrid that overlaps and place infill material to separate. Geogrid layers need to be separated by a 75 mm layer of infill or approved on-site soils.
- Never compact directly on the geogrid.
- Geogrid must cover the entire curved area.

Place two caps on top of the wall, spaced so a third cap will fit tightly between their widest point

Mark the overlap on the bottom of the center cap

Cut cap on marks to fit between caps

Measure the distance of the gap between the 2 caps (x) at the front of the wall

## Capping Curves

- Place two caps on top of the wall, spaced so a third cap will fit tightly between their widest point.
- Set another cap on top of the first two caps in the center and mark where they overlap on the bottom of the center cap.
- Remove the center cap and cut along the marks. Then set in place so the three fit tightly together.
- Repeat this process as often as needed to cap the entire curve.
- It's a good idea to secure caps with a high strength construction adhesive once they are all cut.

More options for finishing your retaining wall.

### Capping Tighter Curves

- For an outside radius, place two caps on top of the wall, with the back of each cap tight together. A gap will appear in the front.
- Measure the distance of the gap between the 2 caps (x) at the front of the wall.
- Measure out this distance (x/2) on the back of each of the cap and mark.
- Draw a line from the mark to the front corner.
- Use a masonry saw to cut each cap.
- The above steps work for both inside and outside radiuses.

More options for finishing your retaining wall.